Leak-free flashing, solid masonry, and a chimney that survives Utah winters
Roof Chimney Repair in Heber City done right the first time
If your chimney is leaking, spalling, or pulling away from the roof, our Roof Chimney Repair in Heber City team finds the source and fixes it. We handle flashing, crowns, mortar joints, and liners for homes across Heber Valley. Winter is coming fast, and a small leak becomes a $4,000 ceiling repair by January. Call us before the first hard freeze.
Live phone supportUpfront optionsBacked workmanship
What's included
What is included in Roof Chimney Repair
Every Roof Chimney Repair in Heber City job starts with a full inspection and ends with a water test. Here is what you get as part of the standard service, and what we treat as an add-on so there are no surprises on the invoice.
Full roof and attic inspection
We inspect the flashing, crown, cap, spark arrestor, brick, mortar joints, and the attic side of the chimney chase. An inspection camera goes down the flue. You get photos of everything we find, whether or not you book the repair.
Flashing rebuild
We remove the old flashing, inspect the decking for rot, and install new copper or stainless flashing with counter-flashing cut into the mortar joint. New flashing is bent on site with a flashing bender to match your roof pitch.
Crown and mortar repair
Cracked crowns get rebuilt with chimney crown mix and a proper drip edge. Failed mortar joints get ground out and repacked with tuckpointing mortar. Spalled brick gets replaced with matching brick where the damage is structural.
Water test and walkthrough
Before we leave, we water-test the repair and check the attic one more time. You get a walkthrough of the finished work, photos, and a workmanship warranty. If anything moves in the next year, we come back at no charge.
Service overview
What Roof Chimney Repair in Heber City actually involves
Roof Chimney Repair in Heber City is the trade of sealing, rebuilding, and re-flashing the point where your chimney passes through the roof plane. That intersection takes more abuse than any other part of the house. We pull the old flashing, inspect the decking and framing for rot, rebuild the cricket or saddle if water is pooling, and re-set new copper or stainless flashing with a proper counter-flashing cut into the mortar joint. Then we address the chimney itself: cracked crown, spalled brick, failed mortar, or a liner that has given up.
Heber City sits at 5,600 feet, and the freeze-thaw cycle here runs from October through April. Water gets into a hairline crack, freezes overnight, expands, and pops the brick face off by spring. That is why we see so many chimney roof leak repair Heber City Utah calls in March and April. Homes in Old Town Heber and along the Center Street Corridor often have original 1940s brick chimneys with mortar that has turned to sand. If you are searching for roof chimney repair in Heber City Utah near me, we are local and we answer the phone.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
How our repair process works
The process flexes to the condition, but these checkpoints keep decisions clear.
Phone intake
Call (855) 927-7517 and describe what you are seeing: staining on the ceiling, a draft, water in the firebox, or brick flakes on the roof. We ask a few questions to narrow down whether this is a flashing issue, a crown issue, or a liner issue. You get a same-day estimate window, usually within 24 hours.
On-site inspection
We get on the roof and into the attic. An inspection camera goes down the flue, and we check the flashing, crown, cap, spark arrestor, and damper. If the leak is intermittent, we run a smoke test equipment setup to trace it. Most inspections take 45 to 60 minutes and you get photos of everything we find.
Written scope and price
You get a clear price before we start. Typical flashing repairs run $450 to $1,200. Crown rebuilds run $600 to $1,500. Full chimney rebuilds start around $3,500. We break out materials and labor so you can see where the money goes, and we tell you what can wait until spring.
The repair itself
Most jobs take two to six hours. We set up roof protection, remove the failed flashing or masonry, and rebuild to code. Tuckpointing mortar gets packed and jointed with a masonry trowel and jointing tool. New flashing is bent on site with a flashing bender so it fits your roof pitch exactly, not a generic piece from a kit.
Test and walkthrough
We water-test the repair and check the attic one more time before we pack up. You get a walkthrough of what we did, photos of the finished work, and a workmanship warranty. If anything moves in the next year, we come back and make it right at no charge.
Tools & methods
Tools and methods we use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Inspection camera
Goes down the flue and into the attic to find cracks, gaps, and damage that are not visible from the ground. Every inspection includes camera footage you can see.
Smoke test equipment
Pushes smoke through the flue to trace leaks and draft problems. It is the fastest way to find intermittent leaks that only show up in certain weather.
Flashing bender
Bends copper and stainless flashing on site to match your exact roof pitch and chimney dimensions. No generic pieces from a kit.
Masonry trowel and jointing tool
Used for tuckpointing, crown repair, and brick replacement. The jointing tool gives the mortar a finished profile that sheds water.
Chimney brush and rods
Removes creosote, soot, and debris from the flue. We size the brush to your flue dimensions so the sweep is thorough without damaging the liner.
Mortar mixing paddle
Mixes refractory mortar and chimney crown mix to the right consistency for the job. Proper mixing is what makes the repair last through freeze-thaw cycles.
Use cases
When to call for Roof Chimney Repair in Heber City
These examples show how the service framework adapts rather than forcing every call through one repair.
Crown rebuild ends freeze-thaw damage
A chimney in Timber Lakes had a crown with three large cracks running through it. Every winter, water got into the cracks, froze, and pushed the crown apart further. The brick below was starting to spall. → We removed the old crown, rebuilt it with chimney crown mix and a proper drip edge, and applied ChimneySaver sealant to the brick. Two winters later, the crown is intact and the spalling has stopped.
Full rebuild saves a leaning chimney
A 1950s brick chimney in the Center Street Corridor had pulled away from the house by about 2 inches at the roofline. The mortar joints were shot, and the flashing had torn loose. The homeowner was told the whole chimney needed to come down. → We rebuilt the chimney from the roofline up, matched the original brick, repointed the lower section, and installed new stainless flashing. The chimney is straight, sealed, and passed inspection. Cost was about a third of a full tear-down.
Problems we solve
Chimney roof damage repair Heber City problems we fix
Most chimney problems in Heber City fall into a handful of categories. Here are the ones we see most often, what happens if you ignore them, and how we fix them.
Water staining on the ceiling near the chimney
We trace the leak with a water test and inspection camera, then repair the actual entry point. Most cases are failed flashing or a cracked crown. We fix both in one visit and water-test before we leave.
Crumbling mortar joints and spalling brick
We grind out the failed mortar and repack it with tuckpointing mortar. Spalled brick gets replaced with matching brick. Then we apply ChimneySaver water repellent sealant to slow future damage.
Smoke backdraft and a stuck damper
We inspect the flue with a camera, sweep out creosote with chimney brushes and rods, and repair or replace the damper. If the liner is damaged, we install a stainless steel chimney liner sized to the appliance.
Animals nesting in the chimney
We remove the nest, sweep the flue, and install a chimney cap with a spark arrestor screen sized to your flue. That keeps animals out permanently and keeps rain and snow out too.
Pricing process
What Roof Chimney Repair costs in Heber City
$450 - $3,500+ depending on scope
Chimney height and roof pitch
A taller chimney on a steep roof takes longer to access and requires more safety setup. A two-story chimney on a 10/12 pitch can add $300 to $600 to the labor cost compared to a single-story chimney on a low pitch.
Extent of hidden damage
If the flashing has been leaking for a while, the roof decking and framing around the chimney may be rotted. Replacing decking adds $150 to $400 per section. We inspect for rot before we quote so there are no surprises.
Crown and brick condition
A simple flashing repair is cheaper than a crown rebuild. If the crown is cracked or the brick is spalling, that work needs to happen too. We break out each item on the quote so you can see the cost of each repair.
How much does roof chimney repair cost in Heber City Utah?
Most repairs run $450 to $1,500 in 2026 pricing. A flashing re-seal or cap replacement sits at the low end. A crown rebuild or partial chimney rebuild runs $900 to $2,500. Full rebuilds start around $3,500. The biggest cost drivers are height, roof pitch, and whether the decking underneath has rotted. We give you a fixed price before we start.
Why is my chimney leaking at the roof in Heber City?
Nine times out of ten it is failed flashing, a cracked crown, or spalled mortar joints letting water in. Heber City's freeze-thaw cycle opens hairline cracks every winter, and by spring the water is inside your attic. Less common causes are a damaged chimney liner or a missing cap. A smoke test and water test pin down the source in under an hour.
Can roof chimney flashing repair stop leaks in Heber City Utah?
Yes, if the flashing is the actual source. We remove the old flashing, inspect the decking, and install new copper or stainless flashing with a counter-flashing cut into the mortar joint. That repair alone solves most chimney roof leak repair Heber City Utah calls. If the leak is coming through the crown or the brick itself, we address that in the same visit.
How long does roof chimney repair take in Heber City Utah?
Most jobs take two to six hours. Flashing repairs and cap replacements are usually done in half a day. Crown rebuilds and tuckpointing may take a full day. Full chimney rebuilds run two to four days because the mortar needs cure time between courses. We tell you the expected timeline before we start so you can plan around it.
Related services
Related Services
Chimney Repair Near Me
General chimney repair covers cracks, loose brick, and damaged caps that are not tied to the roof line. If your Roof Chimney Repair in Heber City inspection turns up issues below the roofline, we handle them in the same visit.
Chimney Masonry Repair
Spalled brick and crumbling mortar joints are the number one cause of chimney deterioration in Heber City. Masonry repair rebuilds the brick face and repoints joints so water has nowhere to sit and freeze.Chimney Crown Repair
The crown is the concrete cap on top of the chimney. When it cracks, water runs straight down the flue. We pour new crowns with a proper overhang and drip edge so Heber City rain and snow shed away from the brick.Ready when you are
Book your Roof Chimney Repair in Heber City today
Every week you wait, water is working its way deeper into your roof deck and framing. We offer same-day estimates, one-visit repairs, and a workmanship warranty on every job. Call (855) 927-7517 and let us stop the leak before the next storm.
Talk with the local team
Request Roof Chimney Repair
Call us at (855) 927-7517 or email info@halewoodpoint.com. We answer the phone during business hours and we have a 24/7 line for emergencies. If you leave a message, we'll call you back the same day. We serve all of Heber City and the surrounding valley.