Cracked crown, wet attic, rusted damper? We fix it right.
Chimney crown repair in Heber City, Utah that stops leaks cold
Chimney crown repair in Heber City, Utah starts with finding where water is actually getting in. A cracked crown lets snowmelt and rain run straight into your flue, and by the time you see a ceiling stain the damage is already working on your liner and framing. We inspect, seal, and rebuild crowns for homes across Heber Valley, from Old Town to Timber Lakes.
Live phone supportUpfront optionsBacked workmanship
What's included
What our chimney crown repair includes
Every crown job we do is quoted as one price with the core work included. Here is what is in the scope, and what we price separately if your chimney needs it.
Full crown inspection
We get on the roof, photograph the crown, and run an inspection camera down the flue. You see the crack, the spalling, or the failed flashing yourself before any work is quoted.
Crown removal and prep
Failed crown material gets chipped or ground out back to sound masonry. We wire-brush the top course and flue tile, and replace any spalling brick with firebrick and refractory mortar before the new crown goes on.
New sloped crown pour
A dedicated chimney crown mix poured 4 inches thick at the center with a 2-inch overhang past the brick face. A bond break at the flue lets the crown and tile move independently so the crown does not tear itself apart.
Water repellent sealing
Once cured, the crown and top courses get a breathable water repellent sealant. It blocks new water from soaking in while letting the masonry dry from the inside, which is what you need in a freeze-thaw climate.
Water test and photos
We water-test the crown and check the flue and attic for moisture before we leave. You get before-and-after photos and the test results, so you know the repair worked.
One-year workmanship warranty
Every crown we pour or seal carries a one-year workmanship warranty. If it cracks or leaks inside that year, we come back and fix it. No arguments, no fine print.
Service overview
Chimney crown repair in Heber City, Utah
Chimney crown repair in Heber City, Utah is the masonry work that rebuilds or reseals the concrete cap on top of your chimney so water runs off instead of soaking in. The crown is the sloped slab sitting above the brick, and it takes the worst of every storm. When it cracks, water follows the crack down through the masonry, into the flue, and eventually into your ceiling. We chip out the failed crown, form a new overhanging pour with the correct slope, and tie it into the flue with a proper bond break.
Most crowns we open up in Heber Valley failed for the same three reasons: hairline cracks from freeze-thaw cycling, a crown poured flat with no overhang, or a crown built from the same mortar as the brick instead of a dedicated chimney crown mix. If your crown is cracked but the brick below is still sound, chimney crown sealing Heber City Utah homeowners ask about can buy you years. If the crown is crumbling into the flue, a full chimney crown rebuild Heber City is the honest answer.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
How our crown repair process works
The process flexes to the condition, but these checkpoints keep decisions clear.
Roof inspection
We get on the roof and look at the crown, the flashing, the cap, and the top few courses of brick. An inspection camera goes down the flue to check the liner for water damage. You get photos of everything we find, not a verbal description. This takes about 30 minutes on a typical Heber City home.
Written scope and price
You get one price for the crown work, itemized. If the flashing is also shot or the cap is rusted through, we tell you and price it separately so you can decide. No pressure, no same-day-only discount games. Most crown repairs land between $350 and $900 depending on size and access.
Crown removal and prep
We grind or chip out the failed crown back to sound masonry, then wire-brush the top course and the flue tile. Any spalling brick at the top gets replaced with firebrick and refractory mortar before the new crown goes on. This prep step is what separates a crown that lasts 20 years from one that cracks in two.
New crown pour
We form and pour a sloped crown using a dedicated chimney crown mix, 4 inches thick at the center with a 2-inch overhang past the brick face. A bond break at the flue lets the crown and the tile expand at different rates without tearing the crown apart. Cure time runs 24 to 48 hours depending on temperature.
Seal and water test
Once cured, we seal the crown and the top courses with a breathable water repellent sealant. Then we run a water test on the crown and check inside the flue and attic for any sign of moisture. You get the test results before we pack up. If it leaks, we are back out on our dime.
Tools & methods
Tools and methods we use on crown work
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Inspection camera
Goes down the flue on every crown call to check for water damage, cracked tile, and creosote buildup you cannot see from the roof.
Smoke test equipment
Confirms whether a leak is coming through the crown, the flashing, or the flue itself before we quote any repair.
Masonry trowel and jointing tool
Used to form the crown, finish the edges, and repoint any mortar joints at the top of the stack that failed alongside the crown.
Angle grinder
Cuts out failed crown material and grinds the top course back to sound masonry so the new crown bonds correctly.
Mortar mixing paddle
Mixes chimney crown mix and refractory mortar to the right consistency for a pour that cures without cracking.
Flashing bender
Forms custom flashing pieces when the crown repair uncovers failed flashing at the roof line.
Chimney brush and rods
Sweeps the flue before crown work so we can see the liner clearly and remove any creosote buildup.
Use cases
When Heber City homeowners call us
These examples show how the service framework adapts rather than forcing every call through one repair.
Flat crown leaking into a Timber Lakes cabin loft
Crown was poured flat with no overhang when the cabin was built. Snow sat on it all winter, water soaked in, and by spring the loft ceiling was wet every time it rained. Liner was starting to rust. → Rebuilt the crown with a steeper slope and wider overhang for the snow load at that elevation. Sealed the top courses. Liner was still sound, so no reline needed. Loft has stayed dry through two winters.
Crown crumbling into the flue on a Red Ledges home
Crown was thin and flat from the original build and had crumbled into the flue. Pieces were blocking the damper, and water was running straight down the inside of the chimney. Homeowner had a stuck damper and a damp smell in the house. → Removed the failed crown, cleaned out the flue, freed the damper, and poured a new crown with a proper slope and bond break. Camera confirmed the liner was still intact. Damper now operates freely and the damp smell is gone.
Problems we solve
Crown problems we fix in Heber City
These are the calls we get most on the Wasatch Back, and what happens if you let them sit through another winter.
Hairline cracks across the crown
If the crown is still structurally sound, we clean out the cracks, fill them with a flexible crown sealant, and coat the whole crown with water repellent. That buys years. If the crack runs through the crown, we rebuild it.
Crown poured flat with no overhang
We chip out the flat crown and pour a new one with a real slope and a 2-inch overhang. That is the fix that stops the water from ever reaching your brick. It is the most common chimney crown rebuild Heber City job we run.
Crown crumbling into the flue
We remove the failed crown, inspect the flue with a camera for damage, and rebuild the crown with a bond break at the flue tile. If the liner is already damaged, we quote relining as a separate line item so you can decide.
Chimney water leak showing on the ceiling
We smoke-test the flue and water-test the crown and flashing to find the actual source. Crown, flashing, or cap, we fix the right thing the first time instead of guessing. Most of these turn out to be crown or flashing.
Pricing process
What chimney crown repair costs
$350 - $1,200 depending on scope
Crown size and shape
A single-flue crown on a small chimney is a smaller pour than a wide multi-flue crown. Material and labor scale with the square footage of the crown, and odd shapes take longer to form.
Roof pitch and access
A steep Old Town Heber roof takes longer to set up on than a low-slope build. We use fall protection and take the time to do it safely, and that labor is part of the quote.
Seal versus rebuild
If the crown is cracked but structurally sound, sealing and water repellent runs at the low end. If it is crumbling or was poured flat, a full rebuild is the only fix that lasts.
How much does chimney crown repair cost in Heber City Utah?
Most crown repairs in Heber City run $350 to $900 in 2026, depending on chimney size, roof pitch, and whether the crown can be sealed or needs a full rebuild. A simple crack seal with water repellent sits at the low end. A full chimney crown rebuild Heber City with new forms and a bond break runs $700 to $1,200. We give you one itemized price before any work starts.
What causes a cracked chimney crown in Heber City?
Freeze-thaw cycling is the main cause. Water soaks into a porous crown, freezes overnight, expands, and splits the concrete. Heber City sees that cycle dozens of times each winter. The second cause is a crown poured flat with no overhang, so water sits on top instead of running off. Third is a crown built from brick mortar instead of a dedicated crown mix, which never had the strength to begin with.
Can chimney crown replacement stop leaks in Heber City Utah?
Yes, if the crown is the source. We water-test the crown and smoke-test the flue before we quote anything, because a leak showing up on your ceiling can also come from failed flashing or a cracked flue tile. When the crown is the culprit, replacement stops the leak immediately. When it is not, we tell you what actually is and price that instead.
How often does a chimney crown need sealing in Heber City Utah?
Every 3 to 5 years for a concrete crown in this climate. A breathable water repellent sealant like ChimneySaver slows the water absorption that drives freeze-thaw damage. We check the crown on every chimney cleaning and let you know if it is due. Skipping the seal is how a $400 crown turns into a $1,200 rebuild plus liner damage.
Related services
Other chimney services we handle
Chimney Repair Near Me
General chimney repair covers everything from crown work to flashing to brick. If your crown is cracked, there is a good chance something below it needs attention too. We inspect the whole stack and quote the full picture in one visit.
Chimney Masonry Repair
Spalling brick and deteriorated mortar joints usually travel with a bad crown. Water gets in at the top and works down. We rebuild the top courses with firebrick and tuckpointing mortar before the new crown goes on so the repair actually holds.
Chimney Relining
A stainless steel chimney liner is the fix when water from a failed crown has already rusted out your old clay tile flue. We camera the flue on every crown call so you know whether relining is in your future before it becomes an emergency.Ready when you are
Get your chimney crown repair in Heber City, Utah scheduled
If your crown is cracked, water is already getting in. Call (855) 927-7517 and we will get eyes on it, usually the same day. One itemized price, photos of everything we find, and a one-year workmanship warranty on the repair.
Talk with the local team
Request Chimney Crown Repair
Call us at (855) 927-7517 or email info@halewoodpoint.com. We answer the phone during business hours and we have a 24/7 line for emergencies. If you leave a message, we'll call you back the same day. We serve all of Heber City and the surrounding valley.