Stainless steel liners installed to NFPA 211, done in a day
Chimney relining in Heber City, Utah that restores safe draft
Chimney relining in Heber City, Utah is the fix when your flue is cracked, corroded, or coated in creosote. We install stainless steel chimney liners sized to your appliance, seal them at the top and bottom, and smoke-test before we leave. If your fireplace smokes, your liner is failing, or an inspector flagged the flue, call (855) 927-7517.
Live phone supportUpfront optionsBacked workmanship
What's included
What our chimney relining service includes
Every reline we quote covers the liner, the hardware, the labor, and the documentation. If something on your chimney needs attention beyond the flue, we tell you before we start so you can decide.
Stainless steel liner
A flexible or rigid stainless steel chimney liner sized to your appliance and flue height. We use HomeSaver, DuraVent, Selkirk, Olympia Chimney Supply, or Copperfield depending on the application and alloy needed.
Insulation wrap
Insulation around the liner keeps flue gas hot, improves draft, and meets code clearance requirements. We wrap where NFPA 211 and the IRC require it and skip it where they do not.
Top plate and cap
A stainless top plate seals the chimney top around the liner. A new chimney cap with spark arrestor keeps rain, birds, and debris out of the flue and protects the liner from weather.
Appliance connection
We connect the bottom of the liner to your fireplace, wood stove, gas insert, or furnace flue collar. Every clamp is torqued and every joint is sealed so no flue gas escapes into the chase.
Smoke test and photos
We run a smoke test with smoke test equipment to confirm no leaks. You get photos of the install, liner spec sheets, and a smoke test result for your records and your insurer.
Service overview
Chimney relining in Heber City, Utah: what it actually is
Chimney relining in Heber City, Utah means installing a new stainless steel chimney liner inside your existing flue so exhaust, smoke, and heat travel up and out instead of into your framing. We pull the old clay tile or rusted steel liner, run a flexible or rigid HomeSaver or DuraVent liner down the chase, wrap it in insulation where code requires, and connect it to the appliance collar and the chimney cap. Every job is built to NFPA 211 and the International Residential Code.
Heber City homes take a beating. Winter swings from 40 degrees to below zero in a day, and that freeze-thaw cycle cracks clay tile and mortar joints. Add creosote buildup from a wood stove or fireplace and you get a damaged chimney liner that leaks carbon monoxide into the house. If you have been searching chimney relining near me Heber City, we handle the diagnosis, the liner, and the paperwork your insurance company wants.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
How our chimney liner installation in Heber City Utah works
The process flexes to the condition, but these checkpoints keep decisions clear.
Inspection first
We run an inspection camera down the flue and check the firebox, damper, crown, and flashing. You see the footage. If the flue is sound and only needs cleaning, we tell you that instead of selling a liner. Most inspections take 30 to 45 minutes.
Sizing and quote
We measure flue height, inside dimensions, and appliance BTU output, then match the liner size to the manufacturer's chart. You get a flat quote the same day. No surprise add-ons for insulation or a top plate.
Old liner removal
We break out cracked clay tile with chimney rods and a chimney brush, then vacuum the flue with HEPA equipment. Debris goes into sealed bags, not your living room. This step runs one to three hours depending on tile condition.
Liner install and connection
We pull the stainless liner down the chase, attach the top plate and chimney cap, and connect the bottom to the appliance or damper. Insulation wrap goes on where code requires it. We torque every clamp and seal every joint.
Smoke test and walkthrough
We run a smoke test with smoke test equipment to confirm no leaks at any joint. Then we walk you through the install, hand over photos and spec sheets, and show you how to check the cap and flashing each season.
Tools & methods
Tools and methods we use on every reline
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Inspection camera
Lets us see every inch of the flue before we quote. We show you the footage so you can see the cracks and gaps for yourself.
Chimney brush and rods
Breaks up creosote and knocks loose tile out of the flue. We run them top-down and bottom-up depending on the chimney layout.
HEPA vacuum
Pulls soot and debris out of the firebox and chase without spreading dust through the house. Every reline runs with one on site.
Smoke test equipment
Confirms the new liner is sealed at every joint. We run smoke through the flue and watch for leaks before we pack up.
Flashing bender
Shapes new flashing around the chimney at the roof line. Proper flashing stops water from running down the chase and into the liner.
Angle grinder
Cuts tile, metal, and hardware to fit. Used on tile removal and on trimming the top plate to the chimney footprint.
Masonry trowel and jointing tool
Used for crown repair, tuckpointing, and firebox mortar work that often happens alongside a reline.
Use cases
When Heber City homeowners call us for relining
These examples show how the service framework adapts rather than forcing every call through one repair.
Timber Lakes cabin stove reline
A cabin wood stove that backdrafted badly at 7,000 feet. The old steel liner was rusted through and creosote had built up over two seasons of heavy burning. → We swept the flue, removed the rusted liner, and installed a new stainless liner sized for altitude with insulation wrap. Draft improved immediately. First fire that night burned clean with no smoke in the room.
Red Ledges gas insert liner
A gas insert venting into an unlined flue. Acidic condensate was corroding the tile and staining the chimney exterior. The homeowner's insurer flagged the flue during a policy review. → We installed a liner rated for acidic condensate, sealed the top plate, and confirmed draft with a smoke test. The insurer received spec sheets and photos. The staining stopped within a season.
Problems we solve
Chimney problems a new liner fixes
Most chimney failures trace back to a damaged liner. Fix the liner and the symptoms stop.
Smoke backdraft into the living room
We size a new stainless liner to the appliance and insulate it so flue gas stays hot and rises. A smoke test confirms the fix before we leave. Most customers see the difference on the first fire.
Cracked clay tile from freeze-thaw
We break out the cracked tile, run a new insulated stainless liner, and seal the top and bottom. The liner keeps flue gas inside and clearances code-correct.
Chimney water leak staining the flue
We trace the leak, repair the flashing or crown, and install a new cap. Then we reline the flue so the new liner starts dry and stays dry.
Creosote buildup from a wood stove
We sweep the flue with a chimney brush and rods, inspect the liner, and reline if the tile is compromised. A clean flue and a new liner bring draft back to spec.
Pricing process
What chimney relining costs in Heber City
$1,800 - $5,500 depending on flue height, liner spec, and tile removal
Flue height and diameter
Taller flues need more liner material, and larger diameters cost more per foot. A 25-foot flue with a 6-inch liner is the common case. A 40-foot flue with an 8-inch liner runs significantly higher.
Tile removal
If the old clay tile is cracked, we break it out before running the new liner. Tile removal adds labor and time. If the tile is sound, we can often run the liner inside it and skip this step.
Liner alloy and insulation
316L stainless costs more than a basic alloy but lasts longer in wood-burning applications. Insulation wrap adds material cost but improves draft and meets code in many installs.
How much does chimney relining cost in Heber City Utah?
Most chimney relining jobs in Heber City run $1,800 to $5,500 in 2026, depending on flue height, liner diameter, and whether we are pulling old clay tile. A straight wood-stove reline on a single-story chimney sits at the low end. Tall chimneys, offsets, and gas inserts with insulation wrap push toward the top. We quote flat after inspection, so you know the number before we start.
How do I know if my chimney needs relining in Heber City?
Three signs point to a failing flue: smoke rolling into the room when you light a fire, a white or black stain on the chimney exterior, and tile shards in the firebox after a cold snap. An inspection camera confirms it. If we see cracked tile, gaps in mortar joints, or a rusted steel liner, relining is the fix. We show you the footage before recommending anything.
What type of chimney liner is best for Heber City Utah homes?
For wood fireplaces and stoves, a 316L stainless steel chimney liner with insulation is the standard. For gas inserts, we use a liner rated for acidic condensate, often aluminum or 316L depending on the appliance. Heber City freeze-thaw cycles crack clay tile fast, so we size the liner to the appliance and insulate it to keep flue gas hot and draft strong.
How long does chimney liner installation take in Heber City Utah?
Most chimney liner installations take four to eight hours, done in one visit. A straight flue with no tile removal runs closer to four. If we have to break out cracked clay tile or work around a chimney offset, plan on a full day. We schedule a smoke test the same day, so you know the flue is sealed before we leave.
Related services
Other chimney services we handle
Chimney Repair Near Me
Relining often pairs with other chimney repair work. If your flashing is leaking or the crown is cracked, we fix those in the same visit so water stops finding its way into the new liner.
Chimney Masonry Repair
Spalling brick and deteriorated mortar joints let water into the chase. We repair the masonry around the flue before or after relining so the new liner is protected from the outside in.Chimney Crown Repair
A cracked chimney crown channels water straight down the flue. We pour a new crown mix or reseal the existing one as part of a reline so the top of the chimney sheds water properly.Ready when you are
Get chimney relining in Heber City, Utah scheduled this week
If your flue is cracked, smoking, or flagged by an inspector, we can help. Flat quote, one-day install for most homes, and a smoke test before we leave. Call (855) 927-7517 and we will get you on the schedule.
Talk with the local team
Request Chimney Relining
Call us at (855) 927-7517 or email info@halewoodpoint.com. We answer the phone during business hours and we have a 24/7 line for emergencies. If you leave a message, we'll call you back the same day. We serve all of Heber City and the surrounding valley.