Stainless steel chimney repair, leak sealing, and pipe replacement across Heber Valley
Metal Chimney Repair in Heber City done right the first time
Metal Chimney Repair in Heber City is what we do when a factory-built or stainless steel flue starts leaking, rusting, or pulling apart at the seams. We handle metal chimney pipe repair, flashing failures, and full metal chimney replacement for homeowners from Old Town Heber to Timber Lakes. If your ceiling has a brown ring after a storm, call (855) 927-7517.
Live phone supportUpfront optionsBacked workmanship
What's included
What our metal chimney repair includes
Every metal chimney repair we do in Heber City starts with a full inspection and ends with a smoke test. Here is what is covered in a standard repair, and what we quote separately if your job needs it.
Full flue inspection
We run an inspection camera down the flue, check every joint and the storm collar on the roof, and look for staining in the attic. You get photos of what we find before we quote the repair.
Leak source repair
We fix the actual entry point, whether that is the flashing pan, the storm collar, the cap, or a joint that opened up. Sealing the ceiling stain without fixing the source just moves the water somewhere else.
Pipe section replacement
Failed sections get cut out and replaced with new stainless pipe matched to your system. We work on Selkirk, DuraVent, and Olympia Chimney Supply pipe and keep common sizes on the truck.
Cap and spark arrestor
A damaged cap or clogged spark arrestor gets repaired or replaced as part of the job. We size it to your pipe diameter so draft stays correct and rain and animals stay out.
Smoke test and cleanup
Before we leave we run a smoke test to confirm the flue drafts and the joints are sealed. Then we sweep the yard with a magnet, walk the roof, and send you photos of the finished repair.
Service overview
What Metal Chimney Repair in Heber City actually involves
Metal Chimney Repair in Heber City is the diagnosis and correction of leaks, corrosion, and structural failure on factory-built and stainless steel chimney systems. That means pulling the cap, running an inspection camera down the flue, checking every joint, storm collar, and flashing pan, then repairing or replacing the failed section. We work on Selkirk, DuraVent, and Olympia Chimney Supply pipe, plus older triple-wall systems that no longer seal the way they did when they were installed.
Heber City winters are hard on metal flues. Snow sits against the pipe for weeks, freeze-thaw cycles work the storm collar loose, and summer UV dries out the sealant until water runs straight down the outside of the pipe. We see metal chimney leak repair Heber City Utah calls most often between November and March, usually after the first big storm pushes water past a failed flashing. If you are searching metal chimney repair in Heber City Utah near me at 9 p.m. with a bucket under the ceiling, that is exactly the call we take.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
How our metal chimney repair process runs
The process flexes to the condition, but these checkpoints keep decisions clear.
Phone triage
You describe the symptom: ceiling stain, rust streaks, smoke in the room, or a cap that blew off. We ask three or four questions, give you a realistic price range over the phone, and book a 2-hour arrival window. Emergency calls after a storm get priority scheduling.
Roof and attic inspection
We go up top and inside. On the roof we check the cap, spark arrestor, storm collar, and flashing pan. In the attic we look for staining on the sheathing and follow the pipe down to the ceiling box. An inspection camera goes down the flue to check for cracked liner sections and creosote buildup.
Written scope and price
You get the findings in plain language plus a fixed price before we touch anything. If the pipe is repairable we say so. If it needs replacement we show you the photos that prove it. No pressure, no upsell on parts you do not need.
Repair or replacement
Most repairs take 2 to 5 hours. We pull the failed section, install new stainless pipe or a replacement storm collar, re-bend the flashing with a flashing bender, and seal every joint with high-temp sealant rated for the flue temperature. Replacement runs 4 to 8 hours depending on roof pitch.
Smoke test and cleanup
We run a smoke test to confirm no draft loss and no leaks at the joints, then check the attic one more time. Magnets sweep the yard for screws, the roof gets a final walk, and you get photos of the finished work plus a written warranty on the repair.
Tools & methods
Tools and methods we use on metal chimneys
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Inspection camera
Goes down the flue to find cracked liner sections, separated joints, and creosote buildup you cannot see from the roof. You get to watch the footage with us.
Flashing bender
Bends new flashing pans on site to match your roof pitch and pipe diameter, so the seal is custom-fit instead of a universal piece that almost works.
Smoke test equipment
Confirms the flue drafts correctly and no joints leak after a repair. We do not call a job done until the smoke goes where it should.
Chimney brush and rods
Clears creosote and debris from the flue before inspection or repair. A clean pipe shows problems a dirty one hides.
Angle grinder and mortar mixing paddle
Used when a metal flue runs through a masonry stack. We grind out failed mortar and mix fresh tuckpointing mortar to seal the assembly around the pipe.
High-temp sealant and water repellent sealant
Seals joints at flue temperatures and protects the surrounding masonry from the freeze-thaw cycle that cracks crowns and loosens flashing.
Use cases
When Heber City homeowners call us
These examples show how the service framework adapts rather than forcing every call through one repair.
Rusted pipe section replaced in Timber Lakes
A cabin flue had rust streaks running down the pipe and a soft spot at the joint. The pipe wall had rusted through from years of snow sitting against it, and the joint had started to separate. → We cut out the rusted section, installed new stainless pipe matched to the existing system, and replaced the cap. The flue passed a smoke test and was back in service the same day. Repair time: 5 hours.
Flashing rebuild fixes recurring leak
A Red Ledges home had been re-sealed twice by another company and still leaked. The flashing pan was undersized for the pipe and the roof pitch, so water was pooling at the base instead of shedding. → We bent a new flashing pan on site with a flashing bender, set it correctly into the roof, and sealed it. Two winters later the attic is dry. Repair time: 4 hours including the roof work.
Problems we solve
Metal chimney problems we fix in Heber City
Most metal chimney calls come down to water, rust, or a joint that let go. Here are the four we see most often in Heber Valley, and what happens if you leave them alone.
Water staining the ceiling around the flue
We trace the water back to the flashing, storm collar, or cap and seal the actual entry point. Most metal chimney leak repair Heber City Utah jobs finish in 2 to 4 hours and stop the stain from growing.
Rust streaks running down the pipe
We cut out the rusted section and replace it with new stainless pipe, then re-seal the joints and check the cap for the source of the moisture. If the rust is surface-only we clean and seal it instead of replacing.
Smoke rolling back into the room
We inspect the full run, re-seal separated joints, clear or replace the cap, and smoke test the flue. If the pipe is crushed beyond repair we quote metal chimney replacement in Heber City Utah with the footage to back it up.
Cap or spark arrestor blown off in a storm
We install a new cap and spark arrestor sized to your pipe, secure it against the wind load Heber City sees, and check the top section of pipe for damage while we are up there.
Pricing process
What metal chimney repair costs in Heber City
$280 - $950 for most repairs; $1,800 - $4,500 for full metal chimney replacement
Roof pitch and access
A steep Heber East Bench roof takes longer to work safely and needs fall protection. A walkable pitch on a North Fields home is a faster job. Access is the single biggest swing factor in the quote.
Length of pipe replaced
A storm collar reseal is a small job. Replacing 4 to 8 feet of stainless pipe with a new cap moves the price up. Full runs past 15 feet usually make more sense as a complete metal chimney replacement in Heber City Utah.
Cap and flashing condition
If the cap and flashing are reusable we reseal them. If the flashing pan is undersized or the cap is bent, new parts get added to the scope. We show you the old parts before we replace them.
How much does metal chimney repair cost in Heber City Utah?
Most metal chimney repairs in Heber City run $280 to $950 in 2026, depending on access and how much pipe needs replacing. A storm collar and flashing reseal sits at the low end. Replacing a 4-foot section of stainless pipe with a new cap lands near the top. Full metal chimney replacement runs $1,800 to $4,500. We give you the exact number before we start.
Can a metal chimney be repaired or does it need replacement in Heber City?
Most metal chimneys can be repaired if the damage is limited to the cap, storm collar, flashing, or one pipe section. Replacement is the right call when the inner liner is cracked, the pipe is crushed, or rust has eaten through the wall. We run an inspection camera down the flue and show you the footage, so you decide with real information instead of a guess.
Why is my metal chimney leaking in Heber City Utah?
The three most common causes we find are a failed flashing pan at the roof line, a storm collar that pulled loose after a freeze-thaw cycle, and a missing or damaged chimney cap letting rain straight into the flue. Snow sitting against the pipe for weeks makes all three worse. We seal the actual entry point, not just the ceiling stain.
Who does stainless steel chimney repair near me in Heber City?
Halewood Point handles stainless steel chimney repair in Heber City and across Heber Valley, including Timber Lakes, Red Ledges, and Old Town Heber. Call (855) 927-7517 and we will book a 2-hour arrival window, usually same day. We work on Selkirk, DuraVent, and Olympia Chimney Supply systems and carry the parts on the truck.
Related services
Other chimney services we handle
Chimney Repair Near Me
General chimney repair covers the whole stack, not just the flue. When we are on your roof for metal work we check the crown, flashing, and cap at the same time, so you are not paying a second trip for a problem we could have caught in the first visit.
Chimney Masonry Repair
Many Heber City homes have a masonry surround with a metal flue inside it. If the brick around your metal pipe is spalling or the mortar joints are failing, we repair the masonry and the flue in the same visit so water stops finding a path in.
Chimney Crown Repair
A cracked chimney crown lets water run down the outside of a metal flue and rust it from the top. We pour a new crown mix with the correct overhang and slope, which is often the cheapest way to stop a metal chimney leak before it reaches the pipe.Ready when you are
Book Metal Chimney Repair in Heber City today
If water is coming in around your metal flue, every storm makes it worse. Call (855) 927-7517 and we will book a 2-hour arrival window, usually same day. Licensed, insured, and we carry the parts on the truck.
Talk with the local team
Request Metal Chimney Repair
Call us at (855) 927-7517 or email info@halewoodpoint.com. We answer the phone during business hours and we have a 24/7 line for emergencies. If you leave a message, we'll call you back the same day. We serve all of Heber City and the surrounding valley.