Firebrick, liners and mortar rebuilt to NFPA 211 spec
Fireplace restoration in Heber City, Utah built to burn safely again
Fireplace restoration in Heber City, Utah means taking a firebox that smokes, spalls or leaks and rebuilding it back to a safe, code-correct burn. We handle fireplace renovation Heber City Utah for homeowners in Old Town Heber, Red Ledges and the Heber Valley who want their hearth working before the cold sets in. Cracked firebrick, a failed damper or a water-stained chimney chase does not fix itself. We diagnose it, price it, and rebuild it.
Live phone supportUpfront optionsBacked workmanship
What's included
What our fireplace restoration service includes
Every restoration is scoped to your fireplace, not a package. Here is what we typically cover. If something on your fireplace does not need work, we say so in the scope instead of adding it to the bill.
Camera inspection and report
We run an inspection camera up the flue and photograph the firebox, damper, smoke chamber and crown. You get a written report with photos the same day, which becomes the basis for the scope.
Firebox rebuild
Failed firebrick comes out and new firebrick goes in, set with refractory mortar rated for the heat. We grind out deteriorated mortar joints and repack them so the firebox holds up through repeated burn cycles.
Damper repair or replacement
We free stuck dampers, replace warped ones, and can install a top-sealing damper that closes tighter than a throat damper. A properly seated damper stops heat loss when the fireplace is not in use.
Chimney relining
If the clay tile liner is cracked or unsealed, we install a stainless steel chimney liner sized to the flue and appliance, insulated where required, and sealed at the top and bottom.
Crown and flashing repair
We rebuild cracked chimney crowns with proper slope and reset or replace flashing where the chimney meets the roof. This is what stops the water leaks that cause most of the damage we see.
Smoke test and walkthrough
Before we leave, we run a smoke test to confirm the draft pulls, check the damper seats, and walk you through the finished fireplace with photos of the flue before and after.
Service overview
What Fireplace restoration in Heber City, Utah actually involves
Fireplace restoration in Heber City, Utah is the repair and rebuild of the firebox, damper, smoke chamber, liner and surrounding masonry so a fireplace drafts correctly and holds heat without pushing smoke into the room. It is not a cosmetic facelift. We pull the firebrick, grind out deteriorated mortar joints, reset the damper, and reline the flue when the existing clay tile is cracked or unsealed. A masonry trowel and jointing tool finish the face; an inspection camera confirms the flue behind it.
Most calls we get start the same way: smoke rolling out of the opening on a cold morning, a damper that will not seat, or a chimney water leak staining the ceiling after a January thaw. In Heber Valley, freeze-thaw cycles run hard from November through March, and that is what cracks chimney crowns and spalls brick. If you have been searching for fireplace restoration near me Heber City, the fix usually starts with a proper inspection, not a guess.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
How our fireplace restoration process runs
The process flexes to the condition, but these checkpoints keep decisions clear.
Inspection
We run an inspection camera up the flue, check the firebox, damper, smoke chamber, crown and flashing, and photograph everything. You get a written report the same day with the failed components called out by name. Takes about 60 to 90 minutes.
Scope and price
You get a line-item scope: what gets rebuilt, what gets relined, what materials we use. No open-ended hourly billing. If the firebox only needs tuckpointing, we say so instead of selling a full rebuild.
Teardown and prep
We lay drop cloths, mask the opening, and remove failed firebrick and loose mortar with an angle grinder and masonry chisel. Dust control runs the whole time. Most teardowns take a half day to a full day depending on how far the spalling goes.
Rebuild and reline
New firebrick set in refractory mortar, a reset or replaced damper, a stainless steel chimney liner sized to the flue, and a rebuilt crown where needed. Mortar gets mixed with a paddle to a consistent spec, not eyeballed. This is the two-to-four-day stretch.
Test and walkthrough
We run a smoke test, check draft, confirm the damper seats, and walk you through the finished fireplace. You get photos of the flue before and after, plus a maintenance schedule. We do not leave until the draft pulls clean.
Tools & methods
Tools and methods we use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Inspection camera
Pushed up the flue to see cracked tiles, gaps in the liner and creosote buildup that you cannot see from the firebox. Photos go into your report.
Chimney brush and rods
Sized to your flue to sweep creosote and soot before restoration. We sweep first so we can see the actual condition of the firebox and liner.
Masonry trowel and jointing tool
Used to set firebrick, pack refractory mortar and finish joints. The jointing tool gives the finished firebox a clean, matched profile.
Angle grinder
Grinds out deteriorated mortar joints and cuts out failed firebrick without damaging the surrounding masonry. Dust control runs the whole time.
Mortar mixing paddle
Mixes refractory mortar to a consistent spec instead of eyeballing it. Consistent mix is what makes the firebox hold up through repeated burn cycles.
Smoke test equipment
Confirms the draft pulls correctly after restoration. We run it before we leave so you see the fireplace working, not just hear that it should.
Flashing bender
Forms new flashing to fit the chimney and roof pitch. Properly bent flashing is what keeps water out at the roof penetration.
Use cases
When to schedule fireplace restoration
These examples show how the service framework adapts rather than forcing every call through one repair.
Red Ledges chimney leak repair and crown rebuild
Water stains on the ceiling next to the chimney after a January thaw. The crown had a hairline crack running the full width, and the flashing had pulled away from the chase. → Crown rebuilt with proper slope, flashing reset with new counterflashing, and the brick sealed with a vapor-permeable water repellent. No leaks through the following winter. Job ran two days.
Timber Lakes reline and cap replacement
Chimney cap blew off in a windstorm and the flue had been open to the weather for a season. The clay tile liner had cracked from water getting in and freeze-thawing. → Stainless steel chimney liner installed and sealed top and bottom, new stainless cap with spark arrestor secured against wind, and the firebox tuckpointed. Job ran four days.
Problems we solve
Fireplace problems we fix in Heber City
Most of the calls we get trace back to one of these. If you are dealing with any of them, a fireplace restoration in Heber City, Utah is usually the fix, not a patch.
Smoke rolling into the room on a cold start
We check the smoke chamber, flue sizing and damper, then correct what is causing the backdraft. Often it is a smoke chamber that needs parging or a flue that is undersized for the opening. We smoke-test after the fix so you see the draft pull.
Cracked firebrick and crumbling mortar joints
We remove the failed firebrick, grind out the deteriorated mortar joints, and rebuild with new firebrick and refractory mortar. We match the joint profile so the finished firebox looks original.
Chimney water leak staining ceilings and rusting dampers
We trace the leak to its source, usually a cracked chimney crown or failed flashing, and repair both. Then we seal the brick with a vapor-permeable water repellent so it stops absorbing water.
Stuck or warped damper that will not close
We free stuck dampers, replace warped ones, and can install a top-sealing damper that closes tighter than a throat damper. Most damper jobs are done in a single visit.
Pricing process
What fireplace restoration costs
$1,800 - $6,500 depending on scope
Scope of the firebox
A firebox that needs a few firebrick replaced costs far less than one that needs a full rebuild. We scope it after the camera inspection, so you know which one you are dealing with.
Liner condition
If the clay tile liner is intact, no reline is needed. If it is cracked or unsealed, a stainless steel chimney liner adds to the scope. Liner work is one of the bigger line items.
Crown and flashing
A cracked crown and failed flashing add repair work. We rebuild the crown and reset the flashing in the same visit, which is cheaper than two separate trips.
How much does fireplace restoration cost in Heber City Utah?
Most fireplace restorations in Heber City run $1,800 to $6,500 in 2026, depending on scope. A firebox rebuild with new firebrick and a damper reset sits at the lower end. Adding a stainless steel chimney liner, crown rebuild and flashing repair pushes it higher. We give you a line-item scope before any work starts, so you know what each part costs.
Can fireplace renovation update my Heber City home?
Yes. A fireplace renovation Heber City Utah project can rebuild the firebox, replace a stuck damper, add a modern chimney cap and spark arrestor, and reline the flue for a new wood or gas insert. It updates how the fireplace looks and how it performs. Many homeowners pair it with new stone facing or a hearth reset while the firebox is already open.
What does masonry fireplace restoration include in Heber City Utah?
Masonry fireplace restoration in Heber City Utah covers the brick-and-mortar side of the fireplace: grinding out deteriorated mortar joints, tuckpointing, resetting spalled brick, rebuilding the firebox with firebrick and refractory mortar, and repairing or rebuilding the chimney crown. It also includes flashing repair where the chimney meets the roof. Structural masonry work is separate from liner and damper work, but we usually scope both together.
How long does fireplace renovation take in Heber City Utah?
A typical fireplace renovation takes two to five days on site. A firebox rebuild with tuckpointing runs about two to three days. Adding a chimney reline, crown rebuild and flashing repair pushes it to four or five. We schedule around your weather window, and we do not leave the fireplace open overnight without sealing it off.
Related services
Related Services
Chimney Repair Near Me
When a fireplace restoration turns up a cracked flue tile or a failed crown, we handle the chimney repair in the same visit. One crew, one scope, no waiting on a second contractor.
Chimney Masonry Repair
Spalled brick and deteriorated mortar joints around the fireplace often extend up the chimney stack. We repair the masonry from the firebox to the crown so the whole structure is sound.
Chimney Crown Repair
A cracked chimney crown is the number one cause of chimney water leaks in Heber City. We rebuild crowns with proper slope and seal them, which protects the restoration work below.Ready when you are
Get your Fireplace restoration in Heber City, Utah scheduled
We inspect, scope and price the job before any work starts. Licensed, insured, and working to NFPA 211 Standard on every restoration. Call (855) 927-7517 and we will get you on the schedule, usually within the week.
Talk with the local team
Request Fireplace Restoration
Call us at (855) 927-7517 or email info@halewoodpoint.com. We answer the phone during business hours and we have a 24/7 line for emergencies. If you leave a message, we'll call you back the same day. We serve all of Heber City and the surrounding valley.