Gas, wood, and insert installs built for Heber Valley winters
Fireplace installation in Heber City, Utah done right the first time
Fireplace installation in Heber City, Utah means cutting a vent, running a liner, and setting a firebox that passes inspection and heats a real room at 6,500 feet. We install gas, wood, and insert units for homeowners across Heber Valley, from Old Town bungalows to new builds at Red Ledges. If you have been searching for a fireplace install in Heber City that handles the whole job, we pull the permit, do the masonry, and test the draft before we leave.
Live phone supportUpfront optionsBacked workmanship
What's included
What our fireplace installation service includes
Every install is quoted as a complete scope, so you know what is covered before we start. Standard work includes the unit set, venting or liner, masonry finish, and testing. Add-ons like full chimney restoration or a new crown are quoted separately and only if your chimney needs them.
Unit set and leveling
We set the firebox or stove level, shim it as needed, and secure it to the floor or hearth. Clearances to combustibles are measured with a tape and matched to the manufacturer's spec. If the opening needs to be cut or enlarged, we do that with an angle grinder and masonry blade.
Vent or liner install
Gas units get direct-vent or B-vent pipe run through the wall or roof. Wood units and inserts get a stainless steel chimney liner sized to the flue, usually 6-inch, insulated for draft. We use brands like Selkirk, DuraVent, and Olympia Chimney Supply.
Firebrick and mortar work
We pack firebrick and refractory mortar around the firebox and rebuild any rough smoke chamber surfaces. Mortar is mixed with a mortar mixing paddle and finished with a masonry trowel and jointing tool. This is the work that keeps the firebox from cracking in the first few seasons.
Crown, cap, and flashing check
We inspect the chimney crown, flashing, and cap while we are on the roof. If the crown is cracked or the flashing has failed, we quote and fix it on the same job. A new cap with a spark arrestor is standard on every install.
Draft and smoke testing
Before we leave, we run a smoke test to confirm the flue pulls correctly and there is no backdraft. On gas units we pressure-test the connection. We verify the damper, spark arrestor, and clearances, and we light the unit with you so you see it working.
Permit and cleanup
We pull the Heber City permit, schedule the inspection, and leave the paperwork with you. Floors are protected before we start, and we haul off the old unit and debris. You should not be able to tell we were there, except for the new fireplace.
Service overview
What fireplace installation in Heber City, Utah involves
Fireplace installation in Heber City, Utah is the full job of setting a new firebox, running the vent or liner, tying into the chimney, and finishing the surround so the unit drafts correctly and meets code. It covers gas direct-vent inserts, wood stoves, and open masonry fireplaces. On a typical job we cut the opening, set the unit level, run a stainless steel chimney liner or DuraVent pipe, pack firebrick and refractory mortar around the box, and fit a new damper and chimney cap. Nothing gets skipped, because a fireplace that drafts wrong smokes the room on the first cold night.
Heber City sits at 5,600 feet with winter lows that drop below zero, so a fireplace here is not decoration, it is heat. Older homes near Center Street Corridor and Old Town Heber often have a cracked chimney crown or a damaged chimney liner that has to be fixed before any new unit goes in. New construction out at Red Ledges and Jordanelle Ridge usually needs a gas fireplace installation Heber City Utah buyers expect, vented through the wall or roof. If you have been typing fireplace installation in Heber City Utah near me into your phone after a cold snap, we handle the whole scope, from the first measurement to the final smoke test.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
How our fireplace install process works
The process flexes to the condition, but these checkpoints keep decisions clear.
On-site assessment
We come out, measure the opening, check the existing chimney with an inspection camera, and look at the crown, flashing, and damper. If the liner is damaged or the smoke chamber is rough, we tell you before quoting. Most assessments take 45 to 60 minutes, and you get a written scope and price the same day.
Permit and materials
We pull the Heber City permit and order the unit, liner, and venting. Brands like Selkirk, DuraVent, and Olympia Chimney Supply are standard for us, and we match the liner to the flue size, usually a 6-inch stainless steel liner for a wood stove or insert. Lead time on most units runs 1 to 3 weeks.
Install day
Our crew protects the floor, sets the unit, runs the liner or vent pipe, and packs firebrick and refractory mortar around the firebox. A straightforward insert install takes one day. A full masonry fireplace with a new crown and cap can run two to three days. We keep the work area clean and haul off the old unit.
Draft and smoke test
Before we call it done, we run a smoke test to confirm the flue pulls correctly and there is no backdraft into the room. We check clearances with a tape, verify the damper and spark arrestor, and confirm the gas connection holds pressure on gas units. If anything is off, we fix it before we leave.
Walkthrough and handoff
We light the unit with you, show you how to run the damper and controls, and hand over the permit paperwork and warranty details. You get a short maintenance schedule, typically an annual sweep and inspection, plus our number for anything that comes up. Most customers are burning within a day of install.
Tools & methods
Tools and methods we use on installs
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Inspection camera
We run a camera down the flue to check the liner, smoke chamber, and damper before quoting. You see the footage, so you know exactly why we are recommending a liner or a crown repair.
Chimney brush and rods
Used to sweep creosote buildup and clear blockages before a new unit goes in. A clean flue is the baseline for correct draft, and we will not set a unit on a dirty chimney.
Masonry trowel and jointing tool
For packing firebrick and refractory mortar around the firebox and finishing joints cleanly. Good trowel work is what keeps a firebox from cracking in the first few seasons.
Mortar mixing paddle
Mixes refractory mortar and chimney crown mix to the right consistency. Hand-mixed mortar is inconsistent, and inconsistent mortar fails at the first freeze-thaw cycle.
Flashing bender
Bends new flashing to fit the chimney and roof pitch. Pre-bent flashing rarely seals correctly, and chimney flashing failure is the most common source of roof leaks around a chimney.
Angle grinder
Cuts masonry when we need to enlarge an opening or remove a damaged section of brick. We use it with dust control to keep the work area clean and the cut straight.
Smoke test equipment
Confirms the flue pulls correctly and there is no backdraft into the room. We run a smoke test on every install before we call the job done, and we show you the result.
Use cases
When to schedule a fireplace installation
These examples show how the service framework adapts rather than forcing every call through one repair.
Red Ledges gas fireplace install
A new build with a framed opening, a gas stub, and no unit. The builder had left the wall open, and the homeowner wanted a direct-vent gas fireplace finished before the holidays. → We set a direct-vent gas unit, ran the vent through the wall, tied into the gas stub, and pressure-tested the connection. Install took one day, and the finish work was done the next. Inspection passed the first time.
Timber Lakes wood stove with liner
A 1970s cabin with an old smoke dragon stove and a rusted-out metal chimney. Draft was poor, the stove ate wood, and the flashing leaked into the attic every spring. → We removed the old stove and chimney, set a modern EPA-certified wood stove on a new hearth pad, ran an insulated stainless steel liner, and replaced the flashing. Wood use dropped by roughly a third, and the attic leak stopped.
Problems we solve
Fireplace problems we solve in Heber City
Most fireplace calls we get are not really about the fireplace. They are about the chimney behind it. Here are the problems we run into most often on Heber City homes and how we handle them.
Old fireplace smokes the room on every light
We inspect the flue with an inspection camera, check the smoke chamber and damper, and size a new stainless steel chimney liner to the appliance. On most homes, a correctly sized and insulated liner fixes the draft completely. We run a smoke test before we leave to prove it.
Chimney water leak after a storm
We trace the leak to the source, usually chimney flashing failure or a cracked chimney crown, and fix it. We bend new flashing with a flashing bender, pour a new crown with chimney crown mix, and seal the brick with water repellent sealant. Most leaks are stopped in one visit.
Damaged chimney liner on an older home
We replace damaged liners with stainless steel, sized to the appliance and insulated for draft. If you are already installing a fireplace, adding the liner to the same job saves you a second visit and a second setup. We show you the camera footage so you can see the problem.
Animal nesting in the chimney
We remove the nest, sweep the flue, and install a chimney cap with a spark arrestor so it does not happen again. On new installs, the cap goes on as part of the job. It is a small part that prevents a real problem.
Pricing process
What fireplace installation costs in 2026
$3,500 - $18,000 depending on unit type, liner, and chimney condition
Unit type and size
A gas insert is cheaper than a wood stove, and a wood stove is cheaper than a full masonry fireplace. Size matters too, because a unit sized for a great room costs more than one sized for a den. We size to the room, not to the biggest box on the showroom floor.
Liner length and size
A one-story chimney needs less liner than a two-story, and a 6-inch liner costs less than an 8-inch. Insulated liners cost more than bare ones, but they draft better and build less creosote. On most jobs the liner is the second biggest line item.
Chimney condition
If the crown is cracked, the flashing has failed, or the smoke chamber is rough, that work has to be done. We quote it up front rather than discovering it mid-job. Fixing it during the install is far cheaper than a separate repair visit later.
Questions before we arrive
Frequently asked questions about fireplace installation
How much does fireplace installation cost in Heber City Utah?
Most gas insert installs run $3,500 to $6,500 installed, and wood stove installs with a new stainless steel liner typically land between $4,500 and $8,500 in 2026. A full masonry fireplace with a new crown, cap, and flashing can run $9,000 to $18,000. The unit itself is often half the cost. Chimney condition, liner length, and whether we need to repair a cracked crown or deteriorated mortar joints drive the rest.
What permits do I need for fireplace installation in Heber City?
You need a building permit from Heber City before any new fireplace, wood stove, or gas appliance goes in, and the work has to meet NFPA 211 Standard and the International Residential Code (IRC). We pull the permit for you as part of the job. Skipping it can void your insurance and cause problems at resale. We leave the inspection paperwork with you when we finish.
Who does gas fireplace installation near me in Heber City Utah?
We do. Our crew handles gas fireplace installation Heber City Utah homeowners need, including direct-vent and B-vent units, gas line tie-ins, and venting through the wall or roof. We pressure-test the gas connection before we leave and run a smoke test to confirm draft. If you already have a gas line stubbed, most installs take one day.
Can fireplace install include a chimney liner in Heber City?
Yes, and on most older Heber City homes it should. A damaged chimney liner is the number one reason a new insert smokes the room or fails inspection. We run a stainless steel chimney liner sized to the flue, usually 6-inch, and insulate it for better draft. Adding the liner to the install is far cheaper than doing it as a separate job later.
Related services
Related services we handle
Chimney Repair Near Me
Before a new fireplace goes in, the chimney has to be sound. We repair cracked crowns, damaged liners, and failed flashing as part of the install, so you are not scheduling a second crew. One visit, one fix, one invoice for Heber City homeowners.
Chimney Masonry Repair
New fireboxes need solid masonry around them. We rebuild smoke chambers, replace spalling brick, and reset firebrick with refractory mortar. If your existing chimney is crumbling, we fix it before the new unit goes in, not after.
Chimney Crown Repair
A cracked chimney crown lets water into the flue and rusts out liners. We pour and finish new crowns with chimney crown mix on most installs, which is the cheapest insurance you can buy against a chimney water leak down the road.Ready when you are
Get your fireplace installation in Heber City, Utah scheduled
Call (855) 927-7517 and we will get an estimator to your door, usually the same day. You get a written scope, a real price, and a crew that pulls the permit and cleans up after itself. Licensed, insured, and warrantied work, done by a local crew that plans to be here next winter.
Talk with the local team
Request Fireplace Installation
Call us at (855) 927-7517 or email info@halewoodpoint.com. We answer the phone during business hours and we have a 24/7 line for emergencies. If you leave a message, we'll call you back the same day. We serve all of Heber City and the surrounding valley.