Camera scans, creosote readings, and written findings before you burn
Chimney inspection service in Heber City, Utah you can schedule today
Our chimney inspection service in Heber City, Utah covers the firebox, damper, flue, crown, flashing, and cap in one visit. If you have not had the stack looked at since you bought the house, or you smell smoke on cold mornings, book a chimney inspection Heber City Utah homeowners trust. We tell you what is safe to burn and what needs fixing first.
Live phone supportUpfront optionsBacked workmanship
What's included
What our chimney inspection service includes
Every inspection covers the full venting system, inside and out. If we find something that needs repair, we quote it separately so you can decide on your own timeline. Nothing gets added to the bill without your say-so.
Full flue camera scan
We run an inspection camera the entire length of the flue and record what it sees. Cracks, gaps, missing mortar, and heavy creosote all show up on video, and you get the footage along with our notes.
Firebox and damper check
We inspect the firebox for cracked firebrick, check the damper for smooth travel, and look at the smoke shelf for buildup. A stuck damper or a cracked brick gets flagged before it becomes a bigger repair.
Crown, flashing, and cap review
From the roof we check the crown for cracking, the flashing for lifting edges, and the cap and spark arrestor for damage. These three items cause most chimney water leaks in Heber City, so they get a close look.
Creosote thickness reading
We measure creosote at the flue top, mid-run, and connector, and report the numbers. Anything above 1/8 inch gets a sweep recommendation, and we can usually do it the same visit.
Written report with photos
You get a plain-language summary the same day: safe to burn, safe with repairs, or do not use until fixed. Photos are attached so you can see exactly what we saw and share it with an insurer or buyer.
Service overview
What a chimney inspection service in Heber City, Utah covers
A chimney inspection service in Heber City, Utah is a top-to-bottom evaluation of the venting system that carries smoke and carbon monoxide out of your home. We run an inspection camera up the flue, check the firebox for cracked firebrick, test the damper for smooth travel, probe mortar joints for softness, and look at the crown, flashing, and cap from the roof. You get photos of anything we find, plus a clear note on whether the chimney is safe to use.
Heber City chimneys take a beating. Winter swings from 40 degrees to below zero crack crowns and pop brick faces, and the freeze-thaw cycle around Jordanelle Ridge and the East Bench works mortar joints loose year after year. Add a wood stove running six months straight and creosote buildup climbs fast. That is why we recommend a chimney safety inspection Heber City homeowners schedule every year before the first hard freeze, not after smoke starts backing into the living room.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
How our inspection visit runs
The process flexes to the condition, but these checkpoints keep decisions clear.
Book the visit
Call and tell us what you burn and when you last had the chimney looked at. We schedule a two-hour window, confirm whether you have a wood stove, fireplace, or furnace flue, and ask about roof access. Same day chimney inspection Heber City slots open most weeks during the shoulder season.
Protect the room
We lay drop cloths from the door to the hearth and set up a HEPA vacuum before any tool comes out. Boots come off or get covered. Fifteen minutes of setup keeps soot off your carpet and out of your HVAC filter.
Inspect the firebox and flue
We check the firebox for cracked firebrick, test the damper for a stuck damper or bent frame, then run an inspection camera the full length of the flue. We log creosote thickness, liner cracks, and any animal nesting in chimney cavities. This is the core of the visit.
Walk the roof and exterior
Up top we check the crown for cracking, the flashing for lifting edges, the cap and spark arrestor for damage, and the brick for spalling. We photograph everything and note the chimney height against the roofline, which matters for draft and for code.
Report and next steps
You get a written report with photos and a plain-language summary: safe to burn, safe with repairs, or do not use until fixed. If work is needed, we price it on the spot. If nothing is wrong, we tell you that too and schedule the next annual visit.
Tools & methods
Tools and methods we use on every inspection
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Inspection camera
Runs the full length of the flue to record cracks, gaps, missing mortar, and creosote glaze that a flashlight from the firebox will never show.
Chimney brush and rods
Used to sweep the flue when creosote reads above 1/8 inch, with brush size matched to the flue dimensions so the liner is not damaged.
Smoke test equipment
Confirms draft and locates leaks in the flue or connectors by introducing smoke and watching where it escapes.
Flashing bender
Shapes new flashing to fit the chimney and roof intersection when the existing flashing has failed and needs replacement.
Masonry trowel and jointing tool
Used for crown repair, tuckpointing, and mortar work when the inspection finds deteriorated joints or a cracked crown.
Mortar mixing paddle
Mixes refractory mortar and chimney crown mix to the right consistency for the repair at hand, whether it is a firebox patch or a full crown pour.
Use cases
When to book a chimney inspection
These examples show how the service framework adapts rather than forcing every call through one repair.
Heavy creosote swept before it lit
A Timber Lakes homeowner burning four cords a season had glaze about 1/4 inch thick near the top of the flue. The chimney had not been swept in three years, and the reading was well past the point where a hot ember could ignite it. → We swept the flue with chimney brushes and rods, cleared the smoke shelf, and re-scanned. The new reading came back under 1/8 inch across all three points. The homeowner booked the next sweep for the following September.
Liner replacement made the fireplace usable
An Old Town Heber home had an original 1940s brick chimney with no liner and two cracked sections in the flue. The fireplace had been unusable for years, and the homeowner assumed it needed a full rebuild. → We installed an insulated stainless steel chimney liner sized to the fireplace, connected it to the firebox and cap, and verified clearances. The fireplace drafts correctly now, and the total cost came in well under a full rebuild.
Problems we solve
Chimney problems our inspection catches early
Most chimney failures start small and give you months of warning. An inspection reads those warnings before they turn into a fire, a leak, or a four-figure rebuild.
Creosote buildup reaching dangerous levels
We measure creosote at three points in the flue and sweep anything above the threshold the same visit. After sweeping, we re-scan to confirm the glaze is gone and log the reading so you can track it season to season.
Chimney water leak staining the ceiling
We trace the leak path from the roof down, checking crown, flashing, and cap in order. Once we find the entry point, we repair it with chimney crown mix or new flashing, then water-test to confirm the fix before we leave.
Damaged chimney liner hidden behind the damper
The inspection camera runs the full length of the flue and records every crack and gap. If the liner is compromised, we quote a stainless steel chimney liner sized to your appliance and explain why a patch will not hold.
Animal nesting in chimney blocking draft
We remove the nesting, sweep the flue clean, and check the cap and spark arrestor for gaps that let animals in. If the cap is missing or damaged, we install a new one so the problem does not repeat next spring.
Pricing process
What a chimney inspection costs in Heber City
$150 - $450 for inspection; $250 - $700 with a sweep depending on creosote volume
Inspection level
A level 1 inspection on an accessible flue is the least expensive. A level 2 adds camera scanning, roof access, and attic or crawlspace checks, which takes longer and costs more. Level 3, which involves opening concealed areas, is quoted per job.
Number of flues
A single-flue fireplace is one price. A chimney with two or three flues, common in older Heber City homes with a fireplace plus a furnace vent, takes longer to inspect and costs more per additional flue.
Roof access and pitch
A steep roof or a chimney with limited access takes more setup and safety gear. We quote based on what we see, and we never cut corners on fall protection to save time.
How much does a chimney inspection cost in Heber City Utah?
Most chimney inspections in Heber City run $150 to $450 in 2026. A basic level 1 inspection on an accessible flue sits at the low end. A level 2 chimney inspection Heber City Utah real estate transactions require, with camera footage and roof access, runs higher. Add a sweep and the total climbs another $100 to $250 depending on creosote volume.
How often should I get a chimney inspection in Heber City?
Once a year if you burn wood, and every other year for a gas furnace flue. Heber City's freeze-thaw cycle damages crowns and mortar faster than a mild climate, so annual checks catch small cracks before water gets in. If you burn more than two cords a season, book the inspection in early fall before the first freeze.
What does a level 2 chimney inspection include in Heber City Utah?
A level 2 inspection adds camera scanning of the entire flue, attic and crawlspace checks for clearance issues, and a roof-level look at the crown, flashing, and cap. It is the standard for home sales, after a chimney fire, or after any event that may have damaged the system. Expect 90 minutes to two hours on site.
Do I need a chimney inspection before selling my Heber City Utah home?
Yes, in practice. Most buyers and lenders ask for one, and a level 2 report answers the liner, clearance, and cap questions up front. It keeps the inspection period from turning into a renegotiation over a chimney nobody documented. We can usually fit a pre-listing inspection within a few days.
Related services
Related Services
Chimney Repair Near Me
When the inspection turns up cracked brick, a loose cap, or a failing crown, we repair it on the same visit or schedule a return trip. Heber City homeowners get a fixed price before we start, not a range that grows once the roof is open.
Chimney Masonry Repair
Spalling brick and deteriorated mortar joints are the two most common findings on Heber Valley chimneys. We rebuild damaged courses with matching brick and repoint joints so the stack sheds water instead of soaking it up.Chimney Crown Repair
A cracked chimney crown is the number one entry point for water. We pour or patch the crown with chimney crown mix, cut a proper drip edge, and seal it so meltwater runs off the stack instead of into the brick.Ready when you are
Book your chimney inspection service in Heber City, Utah
One visit tells you whether your chimney is safe to burn this winter. Call Halewood Point and we will schedule a chimney inspection in Heber City at a time that works, with a written report the same day.
Talk with the local team
Request Chimney Inspection Service
Call us at (855) 927-7517 or email info@halewoodpoint.com. We answer the phone during business hours and we have a 24/7 line for emergencies. If you leave a message, we'll call you back the same day. We serve all of Heber City and the surrounding valley.