Tuckpointing, crown repair and full rebuilds done code-correct
Brick Chimney Repair in Heber City built for Utah winters
Brick Chimney Repair in Heber City means fixing the mortar, brick and crown before another freeze-thaw cycle pulls your stack apart. We work on older masonry in Old Town Heber, newer builds up at Red Ledges, and cabin chimneys in Timber Lakes. If you have spalling brick, a cracked crown or a leak staining the ceiling, we diagnose it, price it upfront and fix it. Licensed, insured, and we clean up when we leave.
Live phone supportUpfront optionsBacked workmanship
What's included
What is included in brick chimney repair
Every brick chimney repair job includes the inspection, the written scope, the masonry work itself, and a documented closeout with photos. Add-ons like liner replacement, cap installation or full waterproofing are quoted separately so you can see exactly what each piece costs.
Full roof and flue inspection
We inspect the crown, cap, spark arrestor, flashing, brick faces, mortar joints, damper and firebox, plus a camera scan of the flue. You get photos of anything we find, whether or not you hire us for the repair.
Mortar joint grinding and repacking
Failed mortar is ground out to a minimum 3/4 inch depth with an angle grinder and diamond blade, then repacked with tuckpointing mortar matched to the original color and hardness. This is the core of most repairs.
Spalled brick replacement
Brick with a popped or crumbling face is cut out and replaced with matching units set in refractory mortar. We match size, color and texture as closely as the local supply allows so the repair blends into the wall.
Crown rebuild or repair
Cracked or flat crowns get rebuilt to a proper slope with a 2-inch overhang so water sheds off the stack. Minor cracks are patched with chimney crown mix and sealed. The crown is the most important water-control detail on the whole chimney.
Flashing re-bend and seal
Old flashing is removed, new copper or aluminum is bent with a flashing bender, and it is sealed into both the roof and the brick. This is where most chimney leaks actually start, and it is where we spend the most time getting it right.
Water repellent sealant application
After the mortar cures, we apply a vapor-permeable water repellent sealant across the stack. It keeps liquid water out while letting the brick breathe, which is what prevents the next round of spalling through a Heber City winter.
Service overview
What Brick Chimney Repair in Heber City actually involves
Brick Chimney Repair in Heber City is masonry work that restores the structural and weather-tight integrity of a brick chimney: grinding out failed mortar and repacking it with fresh tuckpointing mortar, replacing spalled or cracked brick, rebuilding the crown, and re-sealing flashing where the stack meets the roof. Most of the damage we see is water damage, not fire damage. Brick is porous. Once mortar joints crack, water gets in, freezes overnight, expands, and pops the face off the brick. We stop that cycle at the source.
Heber City sits at roughly 5,500 feet, and that elevation drives the work. We swing from 95-degree July afternoons to single digits in January, and that range is brutal on masonry. Chimneys on 1970s and 1980s homes around Center Street Corridor often need full mortar joint replacement, while newer stacks in Valley Hills usually just need crown and flashing attention. If you have been searching brick chimney repair near me Heber City and getting generic answers, the real issue is almost always water entry at the top.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
How our brick chimney repair process works
The process flexes to the condition, but these checkpoints keep decisions clear.
Roof and flue inspection
We get on the roof and inspect the full stack: crown, cap, spark arrestor, flashing, brick faces and mortar joints. Inside, we run an inspection camera up the flue and check the damper and firebox. This takes 45 to 60 minutes and tells us exactly what is failing and why.
Written scope and price
You get a line-item scope: how many square feet of tuckpointing, how many brick to replace, whether the crown gets patched or poured new, and whether flashing needs to be re-bent. One price, valid for 30 days. No change orders mid-job unless you approve them.
Grind out and repack joints
We grind failed mortar to a minimum depth of 3/4 inch with an angle grinder and diamond blade, then pack new tuckpointing mortar with a jointing tool to match the original profile. Mixed on site with a mortar mixing paddle so the color and hardness match the existing brick.
Brick replacement and crown work
Spalled brick gets cut out and replaced with matching units set in refractory mortar. The crown gets rebuilt to a 2-inch overhang with a proper slope so water sheds instead of pooling. On a full rebuild we set the new crown mix and let it cure before we finish the flashing.
Seal, clean up, and document
We re-bend and seal flashing, apply water repellent sealant, and run a smoke test to confirm the flue draws. Then we clean the roof and gutters of mortar dust and send you photos of the finished work. Most repairs take one to two days; a rebuild runs three to five.
Tools & methods
Tools and methods we use on brick chimneys
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Angle grinder with diamond blade
Used to grind out failed mortar joints to a minimum 3/4 inch depth. Cutting to full depth is what makes a tuckpointing repair last instead of failing in two years.
Mortar mixing paddle
Mixes tuckpointing mortar on site so we control the color, consistency and hardness. Pre-mixed bags from a box store rarely match older Heber City brick correctly.
Jointing tool
Packs and profiles the new mortar to match the original joint shape, whether that is concave, V-joint or grapevine. The profile matters for water shedding.
Flashing bender
Bends copper and aluminum flashing on site to fit the exact chimney and roof geometry. Factory-bent flashing rarely fits an older roof correctly.
Inspection camera
Scans the flue and firebox for cracks, gaps and creosote we cannot see from the top or the bottom. This is how we catch liner damage before it becomes a fire risk.
Chimney brush and rods
Removes creosote and soot from the flue. We size the brush to the flue so it scrubs the walls without damaging the liner.
Smoke test equipment
Confirms the flue draws correctly after a repair. If there is a backdraft issue, this is how we find it before you light the first fire.
Use cases
When Heber City homeowners call us
These examples show how the service framework adapts rather than forcing every call through one repair.
Timber Lakes cabin crown rebuild
A cabin chimney at Timber Lakes had a crown that had cracked into four separate pieces and was letting water run down into the firebox. The flashing was original and had pulled away from the brick on the north side. → We removed the old crown, poured a new one with a 2-inch overhang, re-bent the flashing in copper, and sealed the stack. Job took three days including cure time. No water has entered the firebox since, through two winters.
Red Ledges flashing and joint repair
A newer home in Red Ledges had a chimney leak staining the bonus room ceiling. The brick was in good shape but the step flashing had been installed without a proper counter-flashing detail, and three mortar joints near the roofline had opened up. → We removed the old flashing, bent new copper with a proper counter-flashing detail, sealed it into the brick, and repointed the three open joints. One day of work. The ceiling stain has not returned and the repair is documented with photos.
Problems we solve
Chimney problems we fix in Heber City
Most of what we see on Wasatch Back chimneys comes down to water. Here are the specific failures we fix most often, and what happens if they are left alone through another winter.
Spalling brick and crumbling mortar joints
We grind out the failed mortar to 3/4 inch, repack it with matched tuckpointing mortar, and replace the spalled brick. Then we seal the stack so the next freeze-thaw cycle does not start the same problem over again.
Cracked chimney crown leaking into the attic
We rebuild the crown to a proper slope with an overhang, seal it, and check the flashing while we are up there. Most crown leaks stop the same day we finish the pour.
Chimney flashing failure at the roof line
We remove the old flashing, bend new copper or aluminum to fit, and seal it into both the roof and the brick. We also check the counter-flashing and step flashing, which is where a lot of cheap repairs skip steps.
Damaged chimney liner and creosote buildup
We scan the flue with an inspection camera, sweep out creosote with chimney brushes and rods, and repair or reline as needed. If the liner is too far gone, we install a stainless steel chimney liner sized and insulated to NFPA 211.
Pricing process
What brick chimney repair costs in Heber City
$350 - $6,000 depending on scope
Height and roof access
A 12-foot stack on a walkable 4/12 pitch is straightforward. A 25-foot stack on a steep pitch needs staging, harnesses and more labor hours. Access can add 30 to 50 percent to a job.
Square footage of tuckpointing
Tuckpointing is priced by the square foot of chimney face. A small stack might be 20 square feet; a large one can be 60 or more. More area means more grinding and more mortar.
Number of brick to replace
Spalled brick is replaced by the unit. A handful is a small add-on. If more than about 30 percent of the faces are gone, a rebuild is usually the better spend than piecemeal replacement.
How much does brick chimney repair cost in Heber City Utah?
Most brick chimney repairs in Heber City run $350 to $1,800 in 2026. Spot tuckpointing on a few courses starts around $350. A crown rebuild with flashing work typically lands $900 to $1,500. A partial rebuild above the roofline runs $2,500 to $6,000 depending on height and access. Full rebuilds from the foundation up are quoted per job.
Why is my brick chimney cracking in Heber City?
Water is almost always the cause. Heber City swings from 95 degrees in July to below zero in January, and water absorbed into brick and mortar freezes, expands about 9 percent, and pops the brick face off. That is spalling. Cracked mortar joints, a flat or cracked crown, and failed flashing all let water in. Fixing the water path stops the cracking.
Can brick chimney restoration fix spalling bricks in Heber City Utah?
Yes, if the spalling is caught before the brick is structurally compromised. We cut out the spalled units, replace them with matching brick set in refractory mortar, repack the surrounding joints, and seal the stack with a vapor-permeable water repellent. If more than about 30 percent of the brick faces are gone, a rebuild is usually the better spend.
How long does brick chimney tuckpointing take in Heber City Utah?
A typical tuckpointing job on a single-family chimney takes one to two days. Grinding out the joints is the slow part, usually three to five hours on a standard 12-foot stack. Repacking mortar takes another three to four hours. We let the mortar cure 24 to 48 hours before applying sealant, so plan on a two-day window.
Related services
Related Services
Chimney Repair Near Me
If you searched chimney repair near me and landed here, this is the umbrella service. We handle brick, stone, stucco and metal chimneys across Heber City, from a single cracked joint to a full stack rebuild. Call and we will scope it.
Chimney Masonry Repair
Masonry repair covers the brick, block and stone work on your chimney, including brick replacement, mortar repacking and rebuilding damaged courses. It pairs directly with brick chimney repair when the damage is structural rather than just cosmetic.
Chimney Crown Repair
The crown is the concrete cap on top of your chimney, and it is the number one source of water leaks. We rebuild crowns to a proper slope with a 2-inch overhang so water sheds off the stack instead of running down the brick.Ready when you are
Get Brick Chimney Repair in Heber City scheduled this week
Call (855) 927-7517 and we will get a technician on your roof, scope the repair in writing, and give you a price before we start. Licensed, insured, and we clean up after ourselves. If your chimney is leaking right now, say so and we will treat it as an emergency.
Talk with the local team
Request Brick Chimney Repair
Call us at (855) 927-7517 or email info@halewoodpoint.com. We answer the phone during business hours and we have a 24/7 line for emergencies. If you leave a message, we'll call you back the same day. We serve all of Heber City and the surrounding valley.